Corvette C5 Headlight Switch-Blinker Arm Removal

This write-up will show the steps involved with removing the headlight switch / blinker arm / multi-function switch assembly, either for repair or replacement. There wasn’t a good picture-rich write-up that I could find so I documented my process, and maybe it’ll help somebody out.

My particular problem was that when I turn on the headlights, the taillights wouldn’t work and the instrument panel would not illuminate. After removing and repairing my headlight switch, I’m fully functional once again.

Tools Needed:

-Beer of Choice (to be used whenever the heck you feel like it!)

-Torx driver or keys, for the following: T15, T20, and T25.
If you are going to open the headlight switch, add T8 to the list.

-The T25 should be a one-inch bit, OR an L-shaped key with a one-inch leg.

-1/4″ open-end wrench

-Diagonal cutters (optional)

-Flat-bladed screwdriver or other thin prying device

10mm socket, 4mm socket, 7mm socket, socket wrench, and 6″ extension (or equivalent set of nut-drivers)

The Procedure:

In order to get to the blinker switch, we’ll be removing the knee panel that goes under and beside the steering wheel; the steering column covers; and we’ll loosen the center console pieces. Here’s how to do all this.

0. Turn the steering wheel such that the TOP of the wheel is facing LEFT. You’ll see why in step 10.

1. First, I’d recommend loosening the center console and radio bezel. This just makes it easier/safer to remove the paneling around the steering wheel I think. For a good procedure on this, check out this guide at Vette Essentials:

Beginning with step 2 in that guide, it’ll show you how to remove/loosen these pieces. That guide also parallels some of my write-up here, so you can refer to that guide for additional pictures/info. Once you have those panels removed or loose, come back here and continue on!

2. Remove the trunk release switch panel by using a flat screwdriver or somesuch to pop it out of the dash panel. It’s connected to a wire which easily unplugs once you pull the switch forward.

Behind this switch is a T15 torx bolt; unscrew that and set aside with the trunk switch.

3. Next, we’ll unscrew the big knee panel under the steering wheel. There are two T15 torx bolts that hold it in place… unscrew those.

4. To remove this panel after having unscrewed those two bolts, you’ll need to pull TOWARDS YOU from the LEFT SIDE of the panel. There are two tight clips that you need to unsnap: (red circles are where these fasteners attach; you’ll see those once you pull the panel off). The blue circle is the wire that was attached to the trunk release button.


5. When you have the left half of the knee panel loose, carefully begin to work the right half of the panel free. The HVAC sensor is attached; so mind the connecting wire (red circle in below picture). It’s easily disconnected; and at that point you should be able to remove the knee panel completely and set it aside.


6. Next, let’s remove the steering column covers. First we’ll need to remove the bottom half. It’s held on by two T20 screws, located as follows:


Once those screws are out, gently pull downward on the bottom half. It will separate from the top half… they are connected at this point solely by plastic latches (red circles) and hooks (blue circle), as shown below. With some maneuvering, the bottom piece will come free. The tricky part is getting it off from and around the tilt steering lever.



7. Unfortunately I didn’t get pictures of this step; but I’ll try to explain the removal of the top half of the steering column: It’s held on by two torx bolts from underneath. However, these are not normal torx bolts. Instead of the torx pattern being recessed like most bolts; this star-pattern is RAISED. I don’t know about you, but I don’t have torx equipment for those bolts. I found that a 4mm socket does the trick nicely. A six-inch extension is preferred to reach the bolts with. There will be one bolt on each side of the steering wheel. You can see them if you can get your head underneath and look up. Unscrew these bolts, and the top half of the steering column cover will come right off.

8. Now we have the headlight switch exposed, but before we remove the thing, let’s tend to the wires first. To get to them easier, I would remove the metal guard that sits behind the knee panel we removed. (It’s got the styrofoam on it). You’ll want the 7mm socket and a 6″ extension to easily do this: Insert the socket/extension through the holes (circled in red) to get at the bolts (circled in blue). Obviously, this picture is AFTER the guard has been detached but you can still see where and how to get at the bolts.


9. The wiring from the headlight switch attaches in two locations to the car: There is a large blue connector and a small black connector. You’ll want to unplug both of these. They are shown below. (To detach the blue connector… push on the small tab (circled in red) and pull apart.



You may also find that the wires from the headlight switch are cable-tied together with some other wires… If this is the case, use some diagonal cutters to cut the tie away so you can fully free the wires from the headlight switch. There is another, larger clasp/cable tie that can simply be undone without cutting it through.

10. Now we can remove the part! For this step you’ll need the T25 bit/driver and the 1/4 open-end wrench. here’s the part, fully exposed: Note there are TWO bolts; both T25’s. The one on top is easy to get at if you tilt the steering down as far as it will go. The one facing forward, however, sits behind the steering wheel.


To remove this, we’ll simply use our 1″ T25 torx bit and the 1/4 inch wrench to turn it from the side: Real easy!



Get these bolts removed, and you’re home free.

One word of advice… when you remove the headlight switch, you may inadvertently beep your horn. The front of the switch has a small brass pin that sticks out, that… upon touching the steel disc at the base of the steering wheel, evidently makes the horn sound off. Remember playing that game “Operation” in preschool? It’s rather like that!

At this point… your switch is free of the car and ready for repair or replacement.

6 responses to “Corvette C5 Headlight Switch-Blinker Arm Removal”

  1. c5bill says:

    Thanks Very helpfull. Gave me the confidence to know what to expect.

  2. Johnny Gerbich says:

    Thanks for the instructions.. You are right on point and I did excatly what you said to do. I was not able to repair the switch and had to order a new one. But the rest was great.

    Johnny in Sonoma county

  3. Dan says:

    Great instructions. Although I broke the plastic clip inserts on the right side of the kick panel but that didn’t prevent me from putting it back together perfectly. There are no cosmetic errors after I was finished and my lights are working perfect. Thank You

  4. Randy Kish says:

    An excellent ‘step by step’ format; even for a 59 year old non-mechanic like me. With websites like these, my ’99 convertible will have many more years of use.

  5. Chris says:

    Great step by step instructions with the photos! Would have been extremely difficult to find all of the screws without your help! Replaced the switch on my ’98 without a problem! Thanks

  6. RICK WOEHLER says:


Leave a Reply

Your email address will not be published. Required fields are marked *